Go Go Babyz Stroller UNIQR User Manual

gogo Kidz® Travelmate  
Safety & Operating  
Instructions  
Model UNIQR  
Go-GoDBownaloabd fryomzW®ww.SComaonuralsp.coom.rAlal MtaniuoalsnSearch And Download.  
Table of Contents  
Safety  
.. ..................................................................................4  
General Information for Attaching the gogo Kidz ............................6  
Attaching to Non-Britax Car Seats...................................................7  
Attaching to a Britax® or Fisher Price® car seat ...........................8  
Commercial Airlines, Car Seats and the gogo Kidz Travelmate......9  
Care and Maintenance..................................................................10  
TABLE OF CONTENTS  
 
iii  
Safety  
DO NOT USE the gogo Kidz® Travelmate until you  
read and understand these instructions. Your child’s  
safety depends on you reading and following these  
instructions.  
!
WARNING: NEVER LEAVE CHILD UNATTENDED.  
!
WARNING: AVOID SERIOUS INJURY FROM FALLING OR  
SLIDING OUT. ALWAYS USE CAR SEAT RESTRAINT SYSTEM.  
Be sure to follow the manufacturer’s instructions on how to  
properly secure your child in their car seat.  
!
WARNING: DO NOT EXCEED WEIGHT AND SIZE LIMITATIONS  
OF THE CAR SEAT MANUFACTURER OR 50 LBS. MAXIMUM.  
This product is to be used as an add-on to you toddler car  
seat. The warnings and instructions are in addition to the  
safety manual provided by your car seat manufacturer.  
!
WARNING: DO NOT LEAVE THE GOGO KIDZ ATTACHED TO A  
CAR SEAT WHILE DRIVING IN AN AUTOMOBILE. THE GOGO KIDZ  
HAS NOT BEEN TESTED IN COMBINATION WITH THE CAR SEATS  
IN ANY CRASH TESTING PROGRAM AND INJURY TO YOUR CHILD  
COULD OCCUR.  
!
WARNING: TO AVOID INJURY, KEEP CHILD AWAY FROM  
TELESCOPING HANDLE AND THUMBSCREWS. THIS IS NOT A TOY.  
!
WARNING: ALWAYS ENSURE THUMBSCREWS ARE TIGHT  
WHENEVER THE GOGO KIDZ IS ATTACHED TO THE CAR SEAT.  
Injury to your child could result if the unit were to come off  
accidentally when traveling with your child.  
The thumbscrews may loosen over time or have been  
loosened without a parent's knowledge. Always check the .  
thumbscrews prior to using the gogo Kidz.  
!
WARNING: DO NOT USE WHILE EXERCISING  
Do not use this product while running, jogging, in-line  
skating or participating in other athletic activities.  
SAFETY  
4
 
Safety  
!
WARNING: EXCESSIVE WEIGHT, PARCELS, OR ACCESSORY  
ITEMS PLACED OR HUNG ON THE HANDLE MAY CAUSE THE UNIT  
TO BECOME UNSTABLE.  
Do not place parcels or accessory items on the handle in  
excess of 3 pounds.  
Do not allow children to play with or hang onto the gogo  
Kidz.  
!
WARNING: DO NOT ALLOW CHILDREN TO CLIMB INTO OR OUT  
OF THE CAR SEAT WHILE GOGO KIDZ IS SECURED, UNLESS YOU  
ARE HOLDING THE GOGO KIDZ AND INSTRUCTING THE CHILD.  
!
WARNING: NEVER USE THE GOGO KIDZ ON STAIRWAYS OR  
ESCALATORS.  
!
WARNING: THE GOGO KIDZ IS DESIGNED TO ROLL.  
Make sure the front of the car seat is on the oor and the  
entire unit is on a at surface before letting go of the handle.  
Accessories which are not approved by the manufacturer or  
distributor should not be used.  
!
WARNING: PLASTIC MATERIAL WILL WEAKEN OVER TIME IF  
EXPOSED TO EXCESSIVE HEAT OR LIGHT. USE OF THIS PRODUCT  
SHOULD BE DISCONTINUED 5 YEARS FROM THE DATE OF  
MANUFACTURER, AS SHOWN ON THE PRODUCT.  
SAFETY  
5
 
General instructions for attaching the gogo Kidz®  
Travelmate to your car seat.  
General Attaching  
Information  
PLEASE SEE ASSEMBLY AND ATTACHING GUIDE FOR  
STEP BY STEP INSTRUCIONS  
Most car seats have two ribs that go from top to bottom on the back  
of the car seat with a space between them. The handle area on  
the back of the gogo Kidz plate goes between the ribs in the space  
with the smooth, front side of the plate facing out.  
Align the two support tabs on the bottom of the gogo Kidz plate at  
the bottom of the ribs to help support the car seat.  
Arrows pointing to car seat ribs  
Lay the gogo Kidz plate on the back of the car seat. The wheels  
should be able to rotate freely.  
Use appropriate attachment (i.e. short or long strap, retainer bar or  
j-bolts) and fasten to the plate and car seat.  
NOTE: Some car seats do not have these two long ribs in the back. For  
these types of seats, the support tabs on the bottom of the gogo Kidz  
should be located underneath the base itself.  
NOTE: You may be required to move the bar on the back that adjusts  
shoulder straps to allow the handle to sit properly.  
Arrows pointing to support tabs  
NOTE: The seat recline angle may have to be adjusted to make room for  
the support tabs or the wheels on some seats.  
Attach the tether strap to the handle of the gogo Kidz plate to  
ensure the gogo Kidz is secure.  
RECOMMENDED CAR SEATS  
Attaching the tether clip to the  
gogo Kidz  
The gogo Kidz® Travelmate will accommodate most convertible  
and toddler car seats. Please refer to the list of recommended car  
seats, located on the back page, to ensure a safe t. Go-Go Babyz  
is continually testing new seats with the gogo Kidz and will update  
our web site frequently whenever we discover a new match or to  
conrm which seats will not t with the gogo Kidz. If you do not see  
your car seat listed on the product box or manual, please check our  
web site to see if we have had to opportunity to test it with the gogo  
Kidz.  
6
GENERAL INFORMATION FOR ATTACHING THE GOGO KIDZ TO A CAR SEAT  
 
Instructions below are for attaching to Non-Britax / Fisher Attaching to Non-  
Price Car Seats.  
Britax Car Seats  
You will use two thumbscrews, the short strap with two  
cleats attached by two o-rings and the tether strap from  
the car seat.  
1. Place the seat face down on the oor.  
2. Align the plate.  
Align the two support tabs on the back side of the gogo Kidz plate to the  
bottom of the car seat and lay the gogo Kidz plate on the back of the car  
seat. (Please refer to general information if you are having difculty)  
3. Attach the strap.  
Begin by securing the end of the strap that has only one grommet to either  
the left or right side of the gogo Kidz plate. Insert a thumbscrew into the  
highest hole possible on the plate and thread the thumbscrew into the  
cleat. The strap should be in between the plate and the cleat. Leave the  
strap loose because you will tighten it later. Make sure the strap is not  
twisted. Once one side is attached, thread the strap through the seat belt  
opening of the car seat.  
Make sure tabs align with ribs  
at the bottom of the car seat.  
Use opening if available  
NOTE: The cleat can be relocated if necessary to t the needs of your  
particular car seat. To change the location of the cleat, remove the o-ring  
that attaches the cleat to the strap. Place the cleat over the proper hole  
and replace the o-ring.  
6. Attach the other side of the strap.  
Insert the thumbscrew into the other side of the plate, at the same height  
as the rst side. Begin threading thumbscrew into the cleat. Retighten the  
rst thumbscrew until it is almost ush with the plate Then retighten the  
second thumbscrew again.  
7. Test the connection.  
Adjusting the cleat on the strap  
Once the strap is tightened, lift the car seat and gogo Kidz into the upright  
position and test the connection by pulling on the handle and moving the  
gogo Kidz side to side. Retighten the strap.  
8. Attach the tether strap.  
The tether strap is connected to the car seat and attached onto the handle  
of the gogo Kidz plate (as shown on the general information page).  
NOTE: ALWAYS SECURE YOUR CHILD WITH THE SAFETY HARNESS  
PROVIDED BY THE CAR SEAT MANUFACTURER.  
Leave thumbscrew loose until  
you begin threading opposite  
side, and then tighten  
7
ATTACHING THE GOGO KIDS TO A CAR SEAT  
 
Attaching to the Britax® & Fisher Price® car seats  
Attaching to a  
Britax® or Fisher  
Price® car seat  
NOTE: The gogo Kidz does not attach to the Britax® Parkway™  
To attach to the Britax® or Fisher-Price® car seats, you  
will use two thumbscrews, the retainer bar and the tether  
strap from the car seat.  
1. Place the seat face down on the oor.  
2. Insert retainer bar.  
Place the retainer with the at side lying against the car seat. If you  
are using a Wizard® or Boulevard™ car seat, place the retainer bar  
above the metal bar on the back of the car seat.  
Shown above on Britax®  
Roundabout®  
3. Align the plate.  
Align the support tabs at the bottom of the gogo Kidz plate with the  
bottom of the car seat and lay the gogo Kidz plate on the back of  
the car seat.  
4. Insert thumbscrews.  
Insert the thumbscrews into the two holes located in the center of  
the plate and tighten. You may need to hold the bar closer to the  
plate with your other hand while screwing in the thumbscrews.  
Retighten the rst thumbscrew after tightening the second.  
Shown above on Britax®  
Wizard®  
5. Test the connection.  
Once the retainer bar been attached to the plate and the gogo Kidz  
is secure, lift the car seat and pull the gogo Kidz into the upright  
position. Test the connection by pulling on the handle and moving  
the gogo Kidz side to side. Retighten the thumbscrews as needed.  
6. Attach the versa-tether strap.  
Looking in from the top of the  
seat (above) bottom (below)  
Pull 10 inches of the “versa-tether” strap from the pouch that is  
located on the rear of the seat near the top. Pull the strap over the  
handle and tighten the “versa-tether” by pulling on the end of the  
tether strap. Place excess strap back into the pouch. Tuck in all  
remaining latch and tether straps in order not to get tangled when  
in use.  
NOTE: ALWAYS SECURE YOUR CHILD WITH THE SAFETY HARNESS  
PROVIDED BY THE CAR SEAT MANUFACTURER.  
8
ATTACHING THE GOGO KIDZ TO A BRITAX® OR FISHER-PRICE® CAR SEAT  
 
Does the gogo Kidz® Travelmate t down the aisle of an  
airplane? Can I leave it attached on an airplane? Any  
suggestions about the car seat and the airplanes?  
Commercial  
Airlines, car seats  
and the gogo  
KidTravelmate  
Going Through Security  
Some x-ray machines at the airport may be smaller and your car seat with  
the gogo Kidz Travelmate attached may not t through the machine. We  
suggest asking the Security Personnel to "hand wand" your car seat with  
the gogo Kidz attached just like a stroller. Model UNIQR has quick release  
wheels so if needed you can remove the wheels to allow your car seat to t  
through the smaller machines.  
Airplane Aisles  
The gogo Kidz is 16 ½ inches wide and ts down the aisle of most  
commercial airplanes. However, many car seats are wider and they may  
not t down the aisle of the coach section. A practical approach is to have  
your child out of the seat and expect to carry the seat to your assigned  
seat, once you reach the coach section. The handle on the gogo kidz  
makes this easier to do than carrying the car seat by itself.  
Airplane Seats  
There are dozens of car seat manufacturers with multiple models of car  
seats. THE GOGO KIDZ® TRAVELMATE HAS NOT BEEN TESTED  
IN COMBINATION WITH THE CAR SEATS IN ANY CRASH TESTING  
PROGRAM. Remove the gogo Kidz and either stow it in the overhead bin  
or “gate check it.” Fortunately, the gogo Kidz is very easy to put on and  
take off. Only one thumbscrew needs to be removed for the strap version  
and two thumbscrews for the Britax®, Fisher-Price® and Recaro® seats.  
Note: We recommend you remove the strap and keep it with you if you  
check the gogo Kidz® Travelmate at the gate.  
There have been reports of the aircraft seat belt buckle being stuck behind  
car seats, creating a removal problem at destination. You may wish to ask  
the ight attendant for a seat belt extender to eliminate the potential for this  
problem.  
Other Airplane Information  
and links that offer some very good general information about traveling  
with children on airplanes, safety issues and other practical suggestions.  
We recommend you take the time to review this information.  
COMMERCIAL AIRLINES, CAR SEATS AND THE GOGO KIDZ  
 
9
Care &  
Maintenance  
Before connecting the gogo Kidz to your car seat, make sure  
the unit is assembled correctly and all parts and fasteners are  
secure.  
After assembly pull horizontally on the back of the gogo Kidz  
to make certain the guides are aligned properly and there is no  
slippage.  
Conrm that thumbscrews are tight.  
Periodically check that the handle, axle and wheels are secure.  
Replace any damaged parts immediately.  
Clean with a damp cloth and wipe dry.  
Do not store unit outside exposed to rain or extreme sunlight.  
Do not place heavy items on top of unit when storing it.  
WARNING: PLASTIC MATERIAL WILL WEAKEN OVER TIME IF  
EXPOSED TO EXCESSIVE HEAT OR LIGHT. USE OF THIS PRODUCT  
SHOULD BE DISCONTINUED 5 YEARS FROM THE DATE OF  
MANUFACTURER, AS SHOWN ON THE PRODUCT.  
10  
CARE AND MAINTENANCE  
 
Thank you!  
Thank you for your recent order. We wish you many happy travels  
with your new gogo Kidz® Travelmate!  
Our goal for Go-Go Babyz is to offer innovative, high quality and  
safe products to make life easier when you and your baby are “on  
the go.”  
We welcome suggestions and comments. Go-Go Babyz is  
dedicated to making our current products and features easier  
to use. Please send ideas for new features, products or general  
feedback to us at [email protected].  
In addition, we have created a photo gallery on our web site for  
families, like us, using Go-Go Babyz products. Please feel free  
to email or mail us any photos of you and your children using our  
products and we would be happy to share them on our Family  
Photo Gallery page.  
Thank you again for your purchase. We appreciate your business.  
Sincerely,  
The Go-Go Babyz Family  
Toll Free: 888.686.2552  
THANK YOU  
11  
 

Echo Chainsaw CS 280E User Manual
Eicon Networks Network Card DIVA LAN ISDN User Manual
Field Controls Water Pump 20+UL User Manual
Fisher Price Motorized Toy Car 76937 User Manual
Freestyle Watch FS 1064 User Manual
Fujitsu Laptop SPG B 48 158 User Manual
GE Cable Box A016 1CG User Manual
GE Telephone 29480 User Manual
GE Washer Dryer WCXH208 User Manual
Global Machinery Company Home Safety Product VEC117 User Manual